Apigee-edge onpremises installation host issue

Google Cloud Apigee
1

I was trying to install apigee aio on a centos vm. My 1st question is it possible to ibstall aio in a vm?

and when I am trying to install the setup file through my configuration file I am facing hostip issues…

when I am writing a configuration file I have given my centos IP address for IP1 and the same reflects to ZooKeeper too.

Note: I have also rechecked by changing the /etc/hosts file with my IP address.

INFO: running setup as root
INFO: changing log location to /tmp/setup-root.log
Using defaults from /tmp/config.txt

Service setup apigee-zookeeper

/opt/apigee/apigee-setup/bin/setup.sh: line 354: 127.0.0.1: command not found
apigee-service: apigee-zookeeper: apigee-zookeeper is not running
apigee-configutil: apigee-zookeeper: # OK
apigee-service: apigee-zookeeper: Not running (NO_PIDFILE)
apigee-service: apigee-zookeeper: status=1, continuing
apigee-service: apigee-zookeeper: Not running (DEAD)
apigee-service: apigee-zookeeper: status=3, continuing
apigee-service: apigee-zookeeper: Not running (DEAD)
apigee-service: apigee-zookeeper: apigee-zookeeper is dead
Error: setup.sh: /opt/apigee/apigee-service/bin/apigee-service exited with unexpected status 3

help me to drive through it.

2

@chadalawada venkata harish babu was does hostname -i return ? Yes AIO can be installed in VM, do you prefer K8s or Docker ? check these as well : https://community.apigee.com/articles/42562/apigee-edge-private-cloud-aio-docker-image.html

3

Thanks for the reply @Christin Brown. hostmae -i returns ::1 127.0.0.1 . I do have a look at docker but by primary goal is to install it in a VM or in a physical machine, but to be honest I don’t have an idea about K8s but I come to know that it should have 8cores to do the installation. please guide me for this.

4

ok so you will run into issue if your hostname resolves to localhost. it needs to resolve to your public ip. I would make sure you have done all the prereqs with selinux and the etc/hosts

5

@Christin Brown i have disabled and also changed my etc/hosts file to do the installation. I think I just stepped into the installation part and now its getting error like

pigee-configutil: apigee-openldap: # OK
apigee-configutil: apigee-openldap: # OK
apigee-service: apigee-openldap: Not running (NO_PIDFILE)
apigee-service: apigee-openldap: status=1, continuing
apigee-service: apigee-openldap: OK
apigee-service: apigee-openldap: apigee-openldap is running

Set LDAP ROOTDN password

Error: OpenLDAP password could not be changed
Importing ppolicy olcOverlay
ldap_add: Other (e.g., implementation specific) error (80)
	additional info: User Schema load failed for attribute "pwdMaxRecordedFailure". Error code 17: attribute type undefined
adding new entry "olcOverlay=ppolicy,olcDatabase={2}bdb,cn=config"

Error: sudo-apigee-service: ldapadd exited with unexpected status 80
Error: setup.sh: /opt/apigee/apigee-service/bin/apigee-service exited with unexpected status 80

now its started a little but yet a lot to do

6

Hi @chadalawada venkata harish babu did you resolve this issue ? I have the same error when I’m doing my AIO installation. Can you please your finding.

ERROR:-

9614-zk-error.png
9614-zk-error.png898×381 23.4 KB

7

I am seeing this same issue as well. Am not doing an AIO installation, but installing ds on a node.
My hostname is resolving to the private ip, not public ip - does that matter?
Also, if I uninstall zk and try again, it works. This is baffling

8

It can be that you have multiple IP adresses, and zookeeper quorum will not like that;

See reference: https://docs.apigee.com/private-cloud/v4.19.06/edge-configuration-file-reference

# When "hostname -i" returns multiple IP addresses,# set to "y", to have the installer prompt you to select the IP address to use.
ENABLE_DYNAMIC_HOSTIP=n
9

You have clearly IPV6 and IPV4 addresses returned with hostname -i

See reference: https://docs.apigee.com/private-cloud/v4.19.06/edge-configuration-file-reference

# When "hostname -i" returns multiple IP addresses,# set to "y", to have the installer prompt you to select the IP address to use.
ENABLE_DYNAMIC_HOSTIP=n
10

Thanks Denis!

I did check that, it only has one IP.

The issue was with selinux - I am installing on centos7 and I needed to reboot after disabling selinux. After reboot, installation worked.